Service/Install Guides
e•STROKE® " Piggyback" Replacement Procedure
Form #: EB 03-005
(Download only at this time)
This is the replacement procedure for a (tandem unit) piggyback replacement.
e•STROKE® Service Chamber Diaphragm Replacement Procedure
Form #: EB 03-006
(Download only at this time)
This is the replacement procedure for a service chamber diaphragm replacement.
e•STROKE® Brake Monitoring System Overview
Form #: EB 06-004
(Download only at this time)
This is an introduction to the Gen 2 e•STROKE® Brake Monitoring System.
e•STROKE® Installation Guide
Form #: EB 08-003
(Download only at this time)
This is an installation guide for the e•STROKE® e.S3/Gen 3 System. It is designed to continuously monitor S-Cam Drum Type braking systems while in operation and during stationary brake inspections. The e•STROKE® e.S3/Gen 3 system also includes various diagnostic capabilities as described in this guide.
e•STROKE® GEN3 Post Install Functionality Test
Form #: EB 08-008
(Download only at this time)
The following procedure is intended to test the e•STROKE® system functionality after installation. Following these steps will verify that the system is installed correctly and the vehicles foundation brakes are operating within the recommended limits. The e•STROKE® Gen 3 System will monitor the brake status and display faults through dash mounted warning light(s) or displays.
e•STROKE® Gen1 & 2 Tractor & Trailer Drivers Guide
Form #: EB 08-010
(Download only at this time)
This is an e•STROKE® Gen 1 & 2 tractor and trailer driver’s guide.
e•STROKE® GEN1 & 2 Blink Code Definitions
Form #: EB 08-014
(Download only at this time)
This is a chart of blink code definitions.
e•LINK Blink Code Definitions
Form #: EB 08-015
(Download only at this time)
This is a chart of e•LINK blink code definitions.
e•STROKE® GEN2 Tractor Truck Bus System Schematic
Form #: EB 08-022
(Download only at this time)
This is a three axle wiring schematic for gen 2, tractor/truck/bus.
e•STROKE® SAE Fault Codes
Form #: EB 08-025
(Download only at this time)
This is a SAE J1939 brake stroke alert published fault codes.
e-Stroke® System Installation Inspection Checklist
Form #: EB 09-004
(Download only at this time)
e•STROKE® Inspection Checklist.
MGM Drawing
Form #: 9230100
(Download only at this time)
This is a schematic for e•STROKE® Gen 3, 1-4 axle vehicle.
e•STROKE® CCM Service Kit Instructions for Gen1-Gen2- Tractor/Truck/Bus Applications
Form #: EB 10-002
(Download only at this time)
This procedure provides instruction for replacing Gen 1 and Gen 2 CCM’s with various Gen 3 CCM Service Kits.
e•STROKE® Diagnostic Program User Guide
Form #: EB 11-001
(Download only at this time)
Detailed instructions on how to download and install our diagnostic program.
e•STROKE® Disc Actuator and Harness Install Guide
Form #: EB 13-001
(Download only at this time)
e•STROKE® Disc Actuator & Harness Installation Guide.
e•STROKE® Users Guide for Disc and Drum Brakes
Form #: EB 13-002
(Download only at this time)
e•STROKE® Users Guide for Disc and Drum Brakes.
e•STROKE® Disc Truck/Bus Trouble-Shooting Guide
Form #: EB 13-003
(Download only at this time)
e•STROKE® Disc Truck/Bus Trouble-Shooting Guide.
e•STROKE® CCM Disc System Install Guide
Form #: EB 13-004
(Download only at this time)
This is an installation guide for the CCM on the Gen 3 disc system. The e•STROKE® Gen 3 Disc System is designed to continuously monitor Disc (or a combination of drum and disc) vehicle air brake systems both while in operation and during stationary brake inspections. The e•STROKE® Gen 3 system also includes various diagnostic capabilities as described in this guide.
e•STROKE® Disc Low Lining Clearance Fault Detection
Form #: EB 14-002
(Download only at this time)
This bulletin is to notify e•STROKE® Gen 3 system customers that firmware version V3.25 supports disc caliper low lining clearance detection.
